First of all, ask yourself – do you need to take the back off your watch? In general, you shouldn’t as for most people, taking a watch apart will only lead to it being less good than when it was together. If in doubt, take it to a professional.

That said, watch nerds (WIS’s if you like) quite like looking at the innards of their watch, even if it’s just to photograph the serial number of a new acquisition. If you’re going to send it off to service anyway, there’s maybe lower risk so it can be quite fun.

Get tooled up

There are generally 3 types of watch back – press on, monocoque and screw back.

Those which press on need a knife (or ideally a proper case opener) to prise apart from the case, though some may be held in place with screws. Many cheap quartz watches will have some kind of press-on back, though they’re found on all sorts – usually with a small recess between the lugs that you can insert the knife and twist carefully to pop it off.

Here’s an example – it’s a 1961 Seikomatic “Blue Yacht”, a rare and beautiful little thing that was only made for a year or so.

P1200137 (2)


It’s vaguely watertight, but “Waterproof” might be stretching it a bit. Let’s just say, don’t wear it when doing the washing up.

Monocoque or unibody

These are cases where to get the movement out, you need to prise the crystal off the front – an operation very much not for the faint hearted, and one that uses a frankly scary-looking tool called a crystal lift, which is basically used to grab the crystal and deform it in a circular fashion so that it can be separated from the watch.

Here’s a crystal lift in action.

Screw-down cases

By far the most popular, these normally come with notches in the case back to facilitate easy removal, though it’s not uncommon to see them with lairy big scratches that show someone has had a go at getting the back off and it hasn’t worked out.

a 20180704_115337

Do not ever use a pair of scissors to try this!Image result for watch case back opener

Some people use a 2-prong opener, though if the case back is good and stuck you might be asking for trouble.

Others will rely on a 3-prong job; the width between the two prongs at the top is adjusted with a thumbwheel, and twisting the handle moves the 3rd one up and down. These can be picked up for a few £ on Amazon or eBay if you’re feeling brave.

Like most tools, the cheap ones probably seem like a good idea until you realise that the metal of the prongs is softer than the metal on your watch back, and gives way only to skite across the back and put a nice big gouge.

Unfortunately, some awkward watch manufacturers put screw-down case backs that don’t have notches or anything to gain purchase on – necessitating more serious pressing/rotating tools, or reverting to a rubber ball…


What to do if your screw-down case back won’t shift?

I’ve had cases where a screw-down case is stuck tight and either won’t shift because it’s got nothing to grip, or it has notches but no amount of pressure with a case back tool was turning it, and I didn’t want to risk engraving the case backs.

So here’s a fairly quick & dirty but effective trick. Clearly, don’t do this unless you’re prepared that it might go horribly wrong. In other words, don’t do it to an heirloom watch worth a fortune. And probably best not to do it in a dusty workshop (ahem).

Put the watch in something secure – ideally a case holder, in a vice.


Take a 15mm or so socket and put a bead of superglue around the business end of it – ie the thin bit that normally goes over a nut you’re using the socket to work on. If you like, put a little glue on the watch back too. Don’t worry about using speciality stuff – I’ve a pack of 8 little tubes for £1 from a Poundstretcher which do just the job.

IMG_20190625_151229 (2)

Now press it on and hold it for a few seconds so you’re sure it’s even…


Leave it for a while – let’s say 30 minutes. Enough time to be sure it’s set nice and tight.


Now carefully and evenly apply a little force (remember – lefty-loosey, righty-tighty) to get the case back moving.


When you’re done, the socket will lift the case back off and you might find that no amount of force would get it off.

Pour a little acetone (nail varnish remover) into the socket and leave it for a minute or so.


Empty out the excess acetone back into the cap of the bottle, attach the socket back on the wrench and give the case back a tap with a rubber mallet or something that will give it a bit of force but not mark it.


Job done. Now to clean off all the superglue residue using the leftover acetone. Just dampen a bit of kitchen paper or a rag, and give it a good rub. Then use a thumbnail or edge of a credit card to scrape it off – comes away easily and quickly and leaves no mark behind.


Now that’s magic!

Warning: Undefined variable $post in /var/www/wordpress/wp-content/themes/newsup/inc/ansar/hooks/hook-index-main.php on line 117

By ewand

14 thought on “How to remove the stuck back of a watch”
  1. Smudger/s.
    Didn’t believe this method would work as my experience with super glue over a number of applications has not been too successful. Had tried the 3 pronged watchmakers back removal tool found in Chinese kits, total failure. In desperation followed your instructions but left it to cure overnight before applying the wrench. Didn’t have a vice, but with a bit of jiggling around with a G clamp found it did the trick and hey presto the back was off. Brilliant. Removal of the remaining super glue with nail varnish remover and a plastic card was equally successful. Thanks for sharing your very clever trick.

    1. thanks – great to hear that it worked out for you. I didn’t invent the trick, and when I first read about it, I was deeply skeptical – but I tried it on a watch that even a proper watchmaker said he couldn’t get the back off… and it worked a treat…

  2. I volunteer at a Thrift Shop and have had a similar problem changing batteries in certain watches with screw backs. Eventually realized they are not over-tightened but that the combination of sweat, grime and corrosion have sealed them closed. I purchased a can of penetrating solvent – spray on liberally, wait a few minutes, and back is invariably freed up and easy to remove with usual instruments.

    1. Good on you for that volunteer work — in addition to your solution to the stuck watch case problem. I was thinking that penetrating oil was the way to go, but the watch that’s stuck is one of my favorites, and I didn’t want to risk gumming up the works. Since it worked for you, I figured I’d go ahead, and it worked perfectly. I’d also second your advice to wait a few minutes. It does take some time for the oil to penetrate.

      The one thing I did differently was to use a needle-point oiler rather than a spray can. These little oilers are readily available (from Amazon, for example) for a few dollars, and they afford pretty good control of the oil. (I bought one of these a while back in large part because I remember my grandfather, a machinist, having one in his shirt pocket at all times.)

      Anyway, thanks for going first.

  3. I wanted to say thanks. Used this method on a Tissot Seastar T.12 automatic and it worked. Waited overnight for the glue to really set. Had tried, on and off, for a few days with three point watch tool and was going to give up. Will remember this for the future. The minute hand had come free and needs to be reset.

    1. Thanks Barry – the first watch I tried it on was a Tissot Seastar PR516 chronograph that had firmly stuck on back; even the watchmaker I took it to said he couldn’t get it off, so I figured there was nothing to lose…

  4. Thanks for sharing! It worked perfectly. I also dabbed some isopropyl alcohol around the case the night before. The watch is 50 years old and the case was never off. The Bulova 11 BLC Swiss movement is a thing of beauty. However, after watching dozens of hours and taking out the click screw just to test the waters, I realize this is extremely difficult. Everything is so small! I need a practice watch before messing with my cherished vintage Bulova.

  5. Very interesting, here because of Tissot SeaStar! Like many others!! Worth a small fortune but will need work done on the case back as previous attempts at trying to remove have either broken tools or scratched the back something chronic!!

  6. Fantastic! By some freak of physics, the watch back twisted off with ease and the socket popped off without acetone.

Leave a Reply

Your email address will not be published. Required fields are marked *